Buying guide
Hyperbaric Chamber Buying Guide: How to Choose the Right One
Most buyers arrive at a hyperbaric chamber quotation with one question — what does it cost — and leave without asking the four that determine whether they have bought the right machine. The specification is not incidental to the result. Two chambers at similar prices can deliver materially different outcomes, and the differences that cause that are all visible before you sign anything.
This guide walks through the specification in the order it should be decided: pressure first, because everything else is subordinate to it, then chamber type, then oxygen delivery, then the non-negotiables, and finally the running cost that most quotations leave out.
1. Decide the pressure before anything else
Pressure is measured in ATA, atmospheres absolute. One ATA is normal sea-level pressure. Every other specification on the quotation is subordinate to this one, because pressure determines what the chamber can achieve at all.
- 1.3–1.4 ATA: the mild range used for wellness and general recovery protocols.
- 1.5–2.0 ATA: the range most clinical programmes operate in.
- 2.0–3.0 ATA: hospital-grade hard-shell chambers for protocols requiring higher pressure.
A supplier quoting "2.0 ATA" without qualifying whether that is a rated maximum or the continuous working pressure is leaving the most important number ambiguous. Ask for the working pressure at which the stated oxygen flow is achieved — a chamber that reaches 2.0 ATA only when empty is a different machine from one that holds 2.0 ATA with an occupant inside.
Equally important is knowing which pressure your intended protocol actually requires. This is a clinical decision, and it should be settled before the equipment conversation starts. If you are still determining it, the honest position is that you are not ready to compare quotations yet.
2. Match the chamber type to the use case
Soft-shell chambers are fabric, fold flat, weigh under 100 kg and run at the milder end of the pressure range. They suit wellness studios, private home use and low-footfall sites where portability matters more than the highest achievable pressure.
Hard-shell chambers are steel or aluminium, hold higher pressure, support BIBS delivery and multiple occupancy, and are a fixed installation. They suit hospitals, multi-seat clinics and anyone whose protocol needs pressure above the soft-shell ceiling.
The trade-off is straightforward: soft shells are cheap, portable and limited; hard shells are expensive, fixed and capable of more. Buying a soft shell for a protocol that needs 2.5 ATA means owning a machine that cannot deliver it, and the sales conversation that produced that outcome is a commercial failure regardless of how well the unit performs within its limits.
3. Establish how oxygen is delivered
This is the specification most often glossed over, and it changes the result more than buyers expect. Three approaches are common:
- Ambient air inflation: the chamber is pressurised with room air and the occupant breathes through a mask. Lower cost, but the gas the occupant breathes is only as good as the room.
- BIBS — Breathing Induced Breathing System: a regulated supply of pure oxygen is delivered under pressure through a mask or hood. This is the clinical standard and the only correct answer for a hospital installation.
- Oxygen-enriched environment: the chamber interior is enriched with oxygen rather than the occupant being fed from a mask. Common in soft-shell wellness units, and it requires strict control of what is permitted inside.
The distinction is not a preference. A chamber pressurised with room air and a chamber pressurised with oxygen behave differently in ways that affect both the protocol and the fire risk, and a quotation that does not specify which one is being sold has not given you enough to compare against anything.
4. Check the things that are not optional
These are the items that separate a medical device from equipment shaped like one. Each should appear as a line on the quotation rather than as a promise in a conversation:
- Pressure vessel certification appropriate to the market of installation.
- Regulatory clearance for the intended use in that market — a device cleared as a general wellness product is not cleared for treatment protocols.
- Fire suppression appropriate to an oxygen-enriched environment, such as a water mist system.
- A documented emergency depressurisation time.
- Intercom or communication that works without the occupant moving.
- Oxygen monitoring inside the chamber, with an audible alarm.
Ask which of these the chamber has as standard and which the supplier intends to add later. "Can be retrofitted" means the quotation you have does not include a requirement you will need, and retrofitting a hard-shell chamber into a compliant clinical installation is not a minor cost item.
5. Price the running cost, not just the purchase
A chamber is an operating asset, not a product. Over a five-year life the consumables and service typically exceed a meaningful fraction of the purchase price, and for an oxygen-fed chamber the oxygen supply is a permanent overhead rather than a one-off.
Ask for the five-year cost of ownership in writing, including filter changes, service intervals, oxygen consumption per session and what a preventive maintenance visit costs. Then ask what is excluded from it. A figure that omits the compressor is not a cost of ownership.
Then ask about capacity, because it is usually the highest-return question on the list. A two-seat hard-shell chamber serves twice the patients of a single-seat unit for not twice the floor area, and often for less than twice the price. Occupancy rate is usually the constraint on a chamber business, not the number of machines.
Session turnaround time matters here too. A chamber that takes 30 minutes between patients and one that takes 15 will, in a full clinic day, serve a materially different number of people from the same room.
Questions that separate suppliers
A supplier who answers all of these plainly is supplying equipment they have stood behind:
- What is the continuous working pressure, and is the rated maximum higher?
- Which oxygen delivery system is fitted as standard?
- Which certifications and clearances does the unit carry, and for which market?
- What is the session-to-session turnaround time?
- What does the chamber measure as at the working pressure — dB(A) at one metre?
- What are the emergency depressurisation and fire-suppression arrangements?
- How many of these chambers are in clinical use, and can we speak to a reference site?
- What is the five-year cost of ownership?
The last two are the ones that determine whether the investment works. Everything else is a specification comparison; those two decide whether the machine earns its place. A supplier who hesitates on either is telling you something useful.
If you want a specification written for your own site — required working pressure, expected daily sessions, available floor area and target budget — send us those four figures and we will map them to a configuration, with the compromises stated plainly rather than buried in a quotation.