Safety & operations

Hyperbaric Chamber Maintenance Guide

OxySoothe Editorial

Chambers fail in a small number of predictable ways, and almost all of them are cheaper to prevent than to fix. The schedule below assumes a chamber in regular clinical or commercial use; a unit running a few sessions a month needs less frequent attention but the same items.

It is also worth being clear that maintenance is not housekeeping. A chamber is a pressure vessel with a fire-suppression system, an oxygen supply and a life-support-adjacent control system, and the items below are the ones that have a documented role in keeping it compliant as well as working.

Daily checks, two minutes

  • Confirm the current chamber pressure reads zero before opening.
  • Check the oxygen supply is available at the required purity.
  • Listen for anything that differs from the usual running sound — a change is the earliest warning you will get.
  • Confirm the emergency depressurisation valve is free and correctly set.
  • Check the fire-suppression system shows charged and healthy.
  • Confirm the intercom works from inside and out.

These take under two minutes and cover the failures that stop a session immediately. The sound check deserves particular weight: an experienced operator will hear a change in a compressor or an air-dryer before any instrument shows it.

Weekly

  • Wipe the interior and check the window seals for wear or compression set.
  • Inspect oxygen delivery masks and hoses for cracking, hardening or perished seals.
  • Verify the internal communications system end to end.
  • Check that the chamber interior and any humidifier are clean and dry.
  • Confirm the operating and emergency controls behave correctly under a functional test.
  • Look for corrosion on any exposed metal, particularly around penetrations and in humid conditions.

Monthly

  • Service the air intake filters — a restricted filter reduces airflow and can raise internal CO₂, which is a patient-safety issue rather than just a performance one.
  • Test the oxygen analyser against a reference, not against itself.
  • Inspect electrical connections, earthing and the integrity of the supply.
  • Check the pressure vessel for surface corrosion, particularly at welds and around penetrations.
  • Review the log of any faults raised since the last check, even if they appeared to resolve themselves.

A fault log is the most useful maintenance tool most chambers do not have. Intermittent faults — a sensor that drops out occasionally, a valve that hesitates — are far easier to diagnose when there is a written history, and far harder when the operator has already forgotten them.

There is a second reason to keep one. Over time, the fault history becomes a picture of which subsystem is ageing. A chamber that repeatedly logs pressure-sensor faults in its third year is telling you something about its remaining life and its likely resale value, and that information is much easier to act on when it has been accumulating in a record rather than in someone's memory.

The log should be somewhere the operators actually write. A spreadsheet on the wall by the chamber works better than a system nobody has logins for.

Annually, and after any incident

Annual service is where the condition of the vessel itself is assessed, the calibration chain is verified against traceable standards, and the safety systems are functionally tested under load. This should be performed by a technician qualified for pressure equipment in your jurisdiction, and it should produce documentation you can hand to an inspector.

The same service is warranted after any over-pressure event, any chamber impact, or any period out of service, regardless of the date of the last visit. Equipment that has been idle is not equipment that has been maintained — corrosion and seal degradation continue whether or not the chamber is running.

Consumables and their intervals

  • Intake filters: 3–6 months in dusty environments, 6–12 months otherwise.
  • Seals and gaskets: inspect at every service, replace on any sign of compression set.
  • Bladder and soft-shell fabric: replace on the manufacturer's schedule or at the first sign of deterioration, whichever comes first.
  • Hoses and connectors: replace when hardened, not when merely dirty.
  • Oxygen analyser cell: replace on its stated life, and calibrate against a certified reference at least annually.

The faults that cause most downtime

In service records, the same handful of issues recur:

  • Blocked intake filters, causing inadequate pressurisation and a fault that reads as a compressor failure.
  • A failing compressor bearing, which is audible long before it fails completely.
  • Expired oxygen analyser calibration, which takes a working unit out of service until recalibrated.
  • Spares held only by the supplier, so any fault becomes a shipping delay measured in weeks.
  • Hardened oxygen tubing, which is frequently mistaken for a concentrator fault.
  • A failed intercom or door interlock, which on some units requires a service visit to reset.

Keeping spares on site

The single most effective availability measure is holding consumables and the most failure-prone spares yourself. Filters, seals, a spare oxygen analyser cell and a spare mask set cover most unplanned stops. Suppliers who supply a recommended spares list with the equipment are worth listening to, and it is entirely reasonable to make holding that list a condition of the purchase.

The second most effective measure is a service contract with a stated response time. In most markets a 48-hour response is achievable; a week is not acceptable for a clinic that books sessions around chamber availability.

Beyond the contract, it is worth confirming where the technician actually comes from. A chamber manufacturer in one country and a service partner in another is common, and the useful question is not whether a partner exists but how many chambers they already service. A partner covering a wide area with a small workshop will struggle on the first call-out; one covering a dense region with several engineers will not.

For multi-site operators the same logic applies more strongly. Standardising on one chamber model across sites makes spares common, makes training portable between technicians, and makes a fault experience learned at one site useful at the next. Standardising on price makes none of that true.

A note on documentation

Every service, every calibration and every replaced part should be recorded with date, what was done, and by whom. For a business treating members of the public, this record is often what an insurer or an inspector asks for first, and reconstructing it later is far harder than keeping it as you go.

If you want a maintenance schedule drafted for a specific chamber model and its duty cycle, or a spares list to quote against, send us the model and the sessions per week and we will work it out.

Tell us your needs

We can tailor a solution for you

Hyperbaric Chamber Maintenance Schedule and Checklist