Product basics
Hyperbaric Chamber Pressure: What ATA Means and Why It Matters
Every hyperbaric chamber specification leads with a pressure figure, and it is the number most often quoted in a way that makes comparison difficult. Two chambers advertised as "2.0 ATA" can behave completely differently. Understanding what the number measures is the fastest way to make a quotation comparable to another.
What ATA means
ATA stands for atmospheres absolute — the total pressure of the environment, counting the pressure of the air itself. One ATA is standard atmospheric pressure at sea level, about 101.3 kPa or 14.7 psi. A chamber at 2.0 ATA is at twice the pressure of sea level, roughly 10 metres of water.
The word absolute is doing real work here. It distinguishes the figure from gauge pressure, which measures above ambient. A vessel rated at 2.0 ATA absolute sitting at sea level shows about 1.0 ATA on a gauge, and at 1,500 metres the same gauge reading corresponds to a lower absolute pressure. For a specification to be compared across sites and elevations, absolute is the only meaningful convention.
The ranges and what they mean in practice
- 1.0–1.3 ATA: barely above ambient. Some wellness units operate here, where the effect is modest and the session is closer to a relaxing environment than a pressure treatment.
- 1.3–1.4 ATA: the common mild range for home and studio use.
- 1.5–2.0 ATA: where most clinical programmes operate.
- 2.0–3.0 ATA: hospital-grade hard-shell territory, for protocols requiring higher pressure.
These boundaries are conventions rather than physics, and they vary by country and by manufacturer. What matters is that the number your protocol specifies and the number your chamber holds are the same one.
What a pressure figure does not tell you
An ATA number on a datasheet is one line in a specification, and on its own it is close to meaningless for comparison. Every figure needs four companions before two quotations can be compared.
- Whether it is the working pressure or the rated maximum.
- Whether it is reached with an occupant inside, or on an empty-vessel test.
- Whether it is absolute or gauge.
- The pressurisation rate, because the figure and the way it is reached describe different sessions.
A supplier who quotes a single ATA number and leaves the other three unstated is not being deceptive, but they have made the figure impossible to compare. Treating such a quotation as incomplete and asking again is reasonable.
The trade-off in higher pressure
Higher pressure is not free, and the cost is often invisible until the quotation arrives. A chamber rated higher needs a stronger vessel, a compressor that can generate a larger differential, and more space around it for service access. Price, floor area and installation cost all follow that step up.
It also changes the session. Gas density rises, so the work of breathing increases, and ear equalisation takes longer to learn. The pressure change rate may need to be gentler at the top of the range, adding minutes to every session. None of this makes higher pressure wrong — it makes it a different product for a different operator, and one to choose deliberately rather than because the headline figure was larger.
The honest way to frame the decision is that higher pressure buys headroom. If a protocol genuinely needs 2.4 ATA, a machine rated to 1.4 ATA is not a cheaper version of the same thing — it is the wrong tool. If the requirement sits at 1.3 ATA, paying for 2.5 ATA buys an option you will not exercise, and the running cost of a bigger machine follows you every year regardless.
Maximum pressure is not working pressure
This is the distinction that causes the most expensive misunderstandings. A chamber may be rated to 3.0 ATA as a structural limit — the pressure at which the vessel is tested and certified — while its working pressure with an occupant inside is lower.
The reason is physical. As pressure rises, the volume of gas a person breathes changes, and so does the physiological load: gas density increases, the work of breathing becomes harder, and for many protocols the usable oxygen concentration delivered by a fixed flow rate falls. Manufacturers set working pressure limits partly to keep the occupant comfortable, not only to protect the steel.
So when a quotation says "maximum 3.0 ATA", ask: what is the continuous working pressure, what is the oxygen flow at that working pressure, and is the figure quoted with an occupant or as an empty-vessel test value? A chamber capable of 3.0 ATA empty and 1.6 ATA with an occupant inside is not unusual, and it is a materially different machine from one that holds 2.4 ATA in use.
What changes as pressure rises
Pressure affects several things at once, which is why a spec sheet covering only ATA is incomplete.
- Gas density rises, so the occupant works harder to breathe. Above roughly 2.0 ATA most protocols add BIBS delivery rather than relying on ambient air.
- The partial pressure of oxygen in the ambient air rises, so even an occupant breathing room air absorbs more oxygen than at sea level. This is the basis of the mild range.
- Ear equalisation becomes harder, and the rate of pressure change matters more than the final figure. A chamber that reaches 2.0 ATA in 60 seconds is a very different experience from one that takes 15 minutes.
- Fire risk changes with the oxygen concentration in the environment, which is why the fire-suppression specification has to match the oxygen delivery method.
- Noise and heat from the compressor rise with the pressure differential being managed.
The pressurisation rate deserves particular attention, because it is frequently omitted from specifications and it determines whether a session is comfortable. A protocol that specifies 2.0 ATA over 20 minutes is not the same as one that specifies 2.0 ATA in 3 minutes, even though both end at the same figure.
Pressure and oxygen delivery are two different things
It is common to see a chamber described by pressure alone, as though that determines the treatment. It does not. Pressure sets the environment; the delivery method determines what the occupant actually breathes.
A chamber pressurised with room air at 2.0 ATA gives an occupant roughly twice the partial pressure of oxygen of sea-level air. The same vessel at 2.0 ATA with BIBS supplying pure oxygen under pressure gives considerably more. Same vessel, same pressure figure, materially different exposure.
When comparing quotations, ask for both: the working pressure and the delivery method, and the oxygen flow at that pressure. A quotation that gives one without the other cannot be compared against another quotation that gives the other.
Altitude changes the arithmetic
This is worth checking if the installation is not at sea level. A chamber rated in atmospheres absolute delivers the same number of atmospheres wherever it sits, so at 1,500 metres the same 1.4 ATA is a larger pressure difference above the local atmosphere than it is at sea level.
The practical consequence falls on the compressor and the vessel rather than on the occupant. The vessel works against a lower local ambient pressure to reach the same absolute figure, which slightly increases the differential the structure carries, and the compressor works harder to produce it. Neither effect is dramatic at most elevations, but it is why a manufacturer will usually ask for the elevation of the installation before quoting.
The same reasoning explains why gauge and absolute figures are not interchangeable, and the conversion is where the errors happen.
Questions to put to a supplier
- What is the continuous working pressure with an occupant inside?
- What is the rated maximum, and what test established it?
- How long does it take to reach working pressure, and can that rate be adjusted?
- What oxygen flow is delivered at working pressure with the specified delivery system?
- Is the pressure figure quoted absolute or gauge, and what are the safety systems rated for at maximum pressure?
So to answer the question directly: ATA decides what a chamber can do, and it is only meaningful once you know whether it is working or maximum pressure, absolute or gauge, and quoted with an occupant or on an empty vessel.
If you are specifying a chamber for a specific protocol, send us the required working pressure, the pressurisation rate and the delivery method, and we will map it to an equipment configuration with the constraints stated rather than assumed.