Product basics
What Is a PSA Oxygen Generator and How Does It Work?
A PSA oxygen generator makes oxygen from the air already in the room. No delivery, no cylinders to change, no liquid to order at 4am. For a hospital, a spa or a large clinic that needs oxygen every hour of every day, that difference decides whether the running cost is a line item or a rounding error.
PSA — pressure swing adsorption — is the technology behind most oxygen plants sold today in the 5 to 100 Nm³/h range. This guide explains the mechanism in enough detail to let you judge equipment on a quotation, then covers the practical limits that decide whether a PSA unit suits your site.
The short answer
A PSA plant compresses ordinary room air to around 7–8 bar, routes it through a molecular sieve, and uses the pressure itself to separate oxygen from nitrogen. Nitrogen is held in the sieve; oxygen passes through and comes out at 90–95% purity. When the sieve saturates, the pressure drops and the nitrogen releases, ready for the next cycle.
That cycle repeats every few seconds. Two or three alternating towers mean there is always one producing while the other regenerates, which is why the output is continuous rather than delivered in bursts — the single most important practical difference from a pressure cylinder.
Why pressure does the separating
Air is roughly 21% oxygen and 78% nitrogen. The two gases differ in molecular size, and that difference is what the process exploits. Nitrogen molecules are small enough to enter the pores of a synthetic zeolite; oxygen molecules are larger and move through more slowly. At high pressure nitrogen is preferentially adsorbed — it gets held in the sieve while oxygen travels on. Reducing the pressure flips the equilibrium and frees the nitrogen.
The important part is what this means in service. There is no chemistry, no consumable reagent, no distillation column, and no cryogenic temperature to maintain. The only moving parts that wear are the compressor and the valves. That is why maintenance is measured in years rather than months, and why the consumables list is short enough to fit on one line.
It also explains why PSA output is not free. The compressed air has to come from somewhere, and that is the compressor's job — which is why the compressor dominates both the capital cost and the running cost of a PSA plant. A PSA unit is, in effect, a very efficient air compressor with a separator attached.
What output you can expect
Output scales with the volume of feed air the compressor can deliver, and that relationship is the single most important number on a datasheet. Oxygen yield is roughly 0.25–0.35 Nm³ per Nm³ of compressed air, depending on working pressure and how much of the feed is recovered rather than vented.
A 20 Nm³/h unit needs a compressor delivering roughly 60–70 Nm³/h of free air. Suppliers who quote a flow rate without quoting the feed air requirement are omitting the number that determines whether the machine can actually reach its rated output. This is the most common gap in quotations we see, and it is worth checking before comparing prices.
Working pressure is the other half of the calculation. Raising the pressure from 7 to 8 bar improves recovery measurably, but it also raises the compressor's power draw and its heat output, and both need somewhere to go. In a plant room without adequate ventilation, the machine will throttle itself — a fault that is usually misdiagnosed as a control problem.
- Check that the feed air figure is stated at the working pressure, not as a free-air figure at ambient conditions.
- Ask for the oxygen purity measured at the outlet, and the instrument used to measure it.
- Confirm the compressor is oil-free if the application is medical-adjacent.
- Verify the unit is rated for continuous duty, not intermittent operation.
- Check the noise specification in dB(A) at a stated distance — this is the figure that matters for a plant room.
Purity in practice
Standard PSA output is 90–95%. That covers the large majority of medical, hospitality and industrial uses. Where a specification calls for 99% or higher, the answer is usually a two-stage PSA rather than a bigger single stage, and the cost difference is significant enough to be worth designing for from the start rather than adding later.
Be precise about what a datasheet claims. "99% oxygen" is not the same claim as "medical grade", and a plant that meets one does not automatically meet the other. Ask which standard the equipment is built to, request the documentation, and confirm whether the certification covers the finished installation or only the vessel.
Purity also has a practical floor. Atmospheric oxygen is only 21%, so 95% represents capturing most of what is available. Pushing higher means discarding more of the feed air, which costs compressor energy for every point gained. That is why 90–95% is the efficient operating range and why claims of 99.9% from a single-stage plant deserve scrutiny.
Where PSA fits and where it does not
PSA is the right answer for demand in the range of roughly 5 to 100 Nm³/h on a continuous basis. It starts within minutes of power-on, holds output through the day, and scales by adding units in parallel rather than by redesigning the plant. For a hospital that expects to grow, parallel scaling is a genuine advantage over a cryogenic plant.
Below about 5 Nm³/h an oxygen concentrator is usually cheaper to run, because the compressor in a concentrator is a small oil-lubricated unit and the capital cost of a PSA plant is not recovered at that volume. Above roughly 100 Nm³/h per train, a cryogenic plant with liquid oxygen backup typically wins on cost — and most large hospitals run both, with PSA carrying the base load and cryogenic covering peak demand and acting as a reserve.
There is a hybrid option worth knowing about: a PSA plant paired with a pressure-swing reserve tank. The tank fills during off-peak hours and covers a compressor failure, which removes the single most disruptive failure mode without paying for a full cryogenic installation.
Efficiency and the load factor question
A plant sized for peak demand runs at partial load most of the time, and oxygen plants are not at their most efficient there. Compressors are designed around a specific operating point, and running well below it costs disproportionately more energy per cubic metre of oxygen produced. This is the most common way a PSA plant ends up costing more to run than its quotation implied.
There are two ways to handle it. The first is modular sizing: several smaller plants in parallel rather than one large one, so that you can shut units down as demand falls. The second is a buffer vessel large enough to let the compressor run at its efficient point for longer stretches. Neither is exotic, but both need to be designed in deliberately — a single oversized machine on a variable load will not deliver the economics its supplier projected.
Ask the supplier for the specific power consumption at your expected load factor, not the rated figure at full output. The difference between those two numbers is usually where the running-cost assumption in the quotation lives.
Installation and integration
A PSA plant is not a standalone box. It needs a prepared room, a dedicated power supply, ventilation for compressor heat, an appropriate location for the oxygen buffer vessel, and — in most jurisdictions — a documented risk assessment for oxygen enrichment in the room. None of this is exotic, but all of it has to be designed in rather than added afterwards.
The buffer vessel deserves particular attention. It smooths the cycle, allows the compressor to be sized for average rather than peak load, and provides a short buffer during a compressor changeover. A plant installed without one is running with a control strategy that fights itself.
Ventilation is the item most often underestimated. An oil-free compressor still produces significant heat, and in a sealed plant room the ambient temperature rises until the machine derates itself — which presents as a mysterious loss of output in hot weather and a return to normal in winter. If the plant room is small, ask for the heat load and make sure the design accounts for it.
Oxygen piping needs its own design consideration. Oxygen accelerates ignition of many materials and is incompatible with some oils and solvents, so pipe material, fittings, sealing methods and any equipment that could introduce a hydrocarbon into the line all have to be specified deliberately. This is an area where local codes vary significantly and where the supplier's installation experience genuinely matters.
Questions worth asking a supplier
A supplier who answers these clearly is usually a supplier whose equipment works:
- What is the feed air requirement, and at what pressure?
- Is the output continuous or intermittent, and what is the turndown ratio?
- Which pressure vessel certifications and regulatory clearances does the unit carry, and for which markets?
- How is oxygen purity measured, how often is the analyser calibrated, and against what standard?
- What is the compressor service interval, and where are spares held?
- What is the five-year cost of ownership at our expected load factor?
The last question is the one that separates a supplier from a vendor. A plant sized for your peak runs at partial load most of the time, and whether the machine holds efficiency at 40% load is worth more than any specification line on the datasheet.
If you are planning a hospital installation or comparing a PSA system against a cryogenic alternative, the sizing is worth doing properly before anything is quoted. Send us your peak and base load figures and we will map them to a configuration.